| Customization: | Available |
|---|---|
| Capacity: | 310 Gallons |
| Color: | White |
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
| Payment Methods: |
|
|---|---|
| Support payments in USD |
| Secure payments: | Every payment you make at Made-in-china.com is protected by the platform. |
|---|
| Refund policy: | Claim a refund if your order doesn't ship, is missing, or arrives with product issues. |
|---|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Model | L(mm) | W(mm) | H(mm) |
| EB-1088 | 1800 | 1300 | 620 |
Packing is the last process of finished product, . Consider to transportation ways and transportation time, we determine the packing ways to aviod defect during transportation.Sticky PE film on surface of bathtub, EPE film must wrap the product at least two layers, the carton or waterproof paper is used outside. Then wooden frame or ply-wood cased is used as per customer's requirement.
Pre-Installation Preparation:
1. Before installing this product, please follow the product plumbing diagram to arrange the water source, power source and sewer pipe. The working water pressure range of the product is 0.2-0.6MPa, and the water source adopts G1/2" pipe thread cold and hot water connector, and its electrical parameters, please refer to the electrical parameters nameplate. The installation place is reserved for 1 1/2" sewer pipe. (Refer to the plumbing and electrical installation drawings attached to the manual)
2. Before installation, please prepare the following tools: Phillips screwdriver, one screwdriver, level, wrench and so on.
Installation steps:
All parts of this product are standardized, please refer to the plumbing diagram and electrical parameter nameplate when installing.
3. Connecting cold and hot water pipes
The hot and cold water pipes are high-pressure resistant reticulated pipes, so please connect them according to the markings on the joints. (Note: A valve must be installed in each of the cold and hot water pipes)
4.Power connection
Firmly connect the power cord of the bathtub to an all-pole disconnected leakage protector (RCD) (32A), and pay attention to waterproofing.
5.Inspection, cleaning and testing
After the completion of the above steps, please clean up the debris in the tub, open the drain, clean it with water, check again whether each function is running normally, and then fill up the water to make sure that there is no leakage in each pipeline.
Vanho Sanitary Products Ltd. is a subsidiary company of Vanho Group, the factory is located in Foshan City, Guangdong province.
The factory was founded in 1997.It covers more than 30000 square meters area for manufacturing bathtubs, steam rooms, sauna rooms ,shower panel and shower rooms.
The company has won honor such as "Chinese famous brand","China Bathroom Luxury Sanitary ware Top 10 brands""AAA credit enterprise".
We care much about factory management, we keep on working building an efficient production,inspection,warehouse and shipment management system,we have an professional team to ensure the material we use is on top quality, defective material is not allowed to be used on our products. From origin and all processing steps we make the finished products meet or beyond the quality standards.We also care about timely delivery and good conditions for cargoes during handling and transportation.
QUALITY CONTROL
Vanho follow "quality come first" as our business philosophy,the factory passed ISO9001:2015 quality management system. All of our products are made of material from famous brands, our engineer and workers are with rich experience in this industry,hence we are confident of our quality. Meantime, we carry out strict quality standards and inspection policy, to ensure all delivered sanitary products are on good conditions.
INTERNATIONAL STANDARDS
All of our material and spare parts meet international standards and workable in Middle East,Europe, America and Australia market, the certificates for this industry such as CE, SARBER can be provided to ensure there's no risk at buyers' side on market. Meantime,our mature after sales service will make your buying no worries.
INNOVATIVE DESIGN
Our rich experienced R&D department always collect the trend of fashion in this industry, our designer never stop finding inspiration , our sales department always keep interactive communication with our buyers, thanks to the excellent team gives us ability to offer new products in innovative and practical design.
The warranty period of all products is 3 years, and the warranty period of the massage pump is 2 years. During the warranty period, if there is a quality problem for non-human reasons, the seller is responsible for providing new qualified products free Replacement for the buyer.
Quality is the life of our company, having a reliable team with strong sense of responsiblity drive us developing with our clients .
The quality of the delivered bathtubs,shower rooms shall meet the quality standards of buyer and shall be in full conformity to the agreement which is mutually confirmed by Vanho and buyers.
According to quality and inspection standards made by Vanho, the bathtubs we sold under shall be considered by the Buyer to be defective if:
1. Colours of products are defective:
a) the colors of acrylic do not correspond to those of the confirmed samples;
b) the colours are with difference or painting on the exposed surface, the colour is darker or lighter or with an uneven tone;
2. Surface of bathtubs is defective:
a) there are visible scratches and marks of mechanical origin on the decorative surface;
b) there are clearly visible dash type surface or damage/scratches or clearly visible point coloration over 0.5mm in diameter allowing a change in color or surface coating;
c) there are dents or any deepening in surface or any bend, which changes the original form of the bathtubs;
3. The function of bathtubs doesn't work:
The function of appliance doesn't work properly, includes pump,mossage,electric wires etc.
Besides, Vanho makes the following sale promises to the products sent out:
1). If there is a malfunction to our products,we will come back to you within 24 hours upon the moment we receive a message from you, no matter it is within or beyond our warranty time.
2). Our warranty time is usually 3 years against the BL date. Vanho will replace the damaged components and fix the problem at our expense if it is within our warranty time.
3).If the products are damaged and it is out of our warranty time, we may charge some cost for sending new replacement, and shipping freight will also be on your account.
4).If the product is damaged by force majeure and it is still within our warranty time, then the cost price will be charged for new replacement.
Related Models:
FAQ Q:Delivery
A:EXW/FOB/CIF/CNF is normally workable for us. Regarding lead time,usually it is 30days.for some items that needed to develop new moulds, the time will be a few days more,that will be around 45 days. Vanho has a professional transportation team,if you have no designated delivery agent,we will arrange delivery for you as soon as production is completed.
Q:Payment
A:The payment term with Vanho is flexible, T/T,LC is normally acceptable, we will make communications in details.
Q:Packaging
A:Vanho can supply polybag packing,carton, wooden case and so on, If you have other requirement, we can make your design according your demands.
Q:Quality
A:Vanho mainly export goods to high requirement markets, our products have SGS salty test report. the quality can bring clients more confident on door hardware business,and help you to consolidate your market share.
Q:How could I receive the goods?
A:For sample order or small quantity order, we suggest to deliver by express,such as DHL, FedEx, EMS. For urgent order, but many goods, we suggest to deliver by air. For large batch order, it is better to deliver by ocean. No matter which way you choose, we will provide you the best services with best price.
Q:Can I make the products with my own logo?
A:Sure, we provide OEM services to you, make your logo on the products and cartons, we have rich experience in this.
Q:I have my own idea to the products, can you help and produce my own products?
A:Sure, ODM service is available to us,our experienced engineer would customize and develop the aluminum profile system for you. Meanwhile, we won't disclose any information of your products to third party.
Q:I want to work with you, but I`m not familiar with your products, how could I do ?
A:We have professional engineers who could design a complete and perfect solution with clear connection diagram for you, with detail introduction to the products, you would find it easy working with us.
){kind=link}